Suntech ST-910 Installation Manual

Introduction to the Suntech ST-910 Installation Manual

The Suntech ST-910 GPS is an advanced solution for vehicle tracking, offering precision and reliability. To ensure the proper functioning of the device, it is essential to perform a correct installation. In this manual, we will cover essential aspects of the physical installation of the ST-910, including the ideal GPS position, power connection, SIM chip installation, and final system verification.

Choosing the GPS position is crucial to maximize signal reception. The device should be installed in a location where it has a clear view of the sky, avoiding obstructions that may interfere with communication with satellites. Furthermore, the power source must be securely connected to ensure that the GPS operates continuously. The installation of the SIM chip should be done carefully, ensuring that it is correctly positioned and activated.

Finally, system verification is a fundamental step to confirm that everything is functioning as expected. Follow the instructions carefully to avoid future problems and ensure that your Suntech ST-910 is ready to provide the best tracking experience.

To further enhance your experience, consider the Trackar platform, which offers a one-time payment system and additional benefits for monitoring your vehicle.

SMS Commands

1. Time Zone Configuration

The first step to configure your GPS tracker is to adjust the time zone. This is crucial to ensure that the location data is accurate and reflects the correct time. Use the command below to perform this configuration.

8960000w00

2. Set Update Time with Ignition On

The update time with the ignition on can be adjusted as desired. The default interval is 60 seconds, which means the tracker will send information every minute while the vehicle is moving or the ignition is on. To change it, use the command below.

8050000 60

The interval is adjustable in seconds.

3. Set Update Time with Ignition Off

Just like the update time with the ignition on, it is possible to set an interval for when the ignition is off. The default is 3300 seconds, equivalent to 55 minutes. Use the command below to configure.

8090000 3300

The interval is adjustable in seconds.

4. Set Carrier APN

It is essential to enter the correct APN, username, and password information, as they vary between chip providers and carriers. Below are the commands for different APNs. Choose the one that corresponds to your carrier.

8030000 allcom.br

8030000 allcom.vivo.com.br

8030000 brt.br

8030000 claro.com.br

8030000 conect.algar.br

8030000 datatem.algar.br

8030000 eseye.com

8030000 gprs.amazoniacelular.com.br

8030000 gprs.oi.com.br

8030000 gprs.telemigcelular.com.br

8030000 jbgprs.algar.br

8030000 linksolutions.br

8030000 m2data.algar.br

8030000 m2data.arqia.br

8030000 m2data.vivo.com.br

8030000 m2m.vodafone.br

8030000 m2track.br,vivo,vivo#

8030000 meta.vivo.com.br

8030000 oktor.br

8030000 sercomtel.com.br

8030000 smart.m2m.vivo.com.br

8030000 ss.algar.br

8030000 tim.br

8030000 tmdata.tim.br

8030000 transmeet.br

8030000 up.m2m.vivo.com.br

8030000 virtueyes.vivo.com.br

8030000 voxter.algar.br nlt nlt

8030000 voxter.br

8030000 wap.ctbc.br

8030000 wl.vivo.com.br

8030000 y1.m2m.algar.com.br

8030000 zap.vivo.com.br

The information must be updated accurately.

5. Activate GPRS Transmission

For the tracker to start sending data, it is necessary to activate GPRS transmission. This will allow the device to send location and status information in real time. Use the command below to activate.

7100000

6. Configure DNS and Port

It is important to correctly configure the DNS server and port to ensure communication of the tracker. The commands below allow you to set up to three servers with their respective ports.

8040000 central.trackar.com.br,5011

7. Activate Movement Alert Without Key

You can adjust the movement alert time without the need for a key. The time is adjustable in minutes and can be configured according to the user's needs. Use the command below to set it.

1810000T180

Special commands

Special Commands

Below are some special commands that can be used for various functions on the tracker.

rconf

Restart

Sleep0000 5

9400000

9410000

6690000

SLEEP0000 10

Reset

format