Softruck E3+ Installation Manual

Introduction to the Softruck E3+ Installation Manual

Welcome to the installation manual for the Softruck E3+, a GPS tracking device designed to ensure safety and efficiency in fleet management. In this guide, we will cover the fundamental aspects of the physical installation of your GPS, including the correct positioning of the device, the necessary power supply, the insertion of the SIM card, and the steps for verification after installation.

The GPS position is crucial to ensure a strong and reliable signal, so choose a location that minimizes obstructions. The power supply should be connected according to the manufacturer's specifications to avoid operational failures. Don't forget to insert the SIM card correctly, ensuring that it is active and has an adequate data plan.

After installation, it is essential to perform a complete verification to confirm that the device is operating as expected. This will ensure that you can make the most of the functionalities offered by the Softruck E3+.

To further optimize your fleet management, consider using the Trackar platform, which offers a one-time payment and advanced resources for monitoring and data analysis. Make the most of your Softruck E3+!

SMS Commands

1. Equipment Activation

To start the communication of the tracker with the chip, it is necessary to send two initial commands. The first command is REG000000# and the second is SMS1.

REG000000#

SMS1

2. Protocol Configuration

Set the communication protocol to TCP to ensure correct data transmission.

TCP

3. Time Zone Configuration

Adjust the device's time zone using the command TZW0.

TZW0

4. APN Configuration

It is crucial to configure the APN, username, and password correctly, as this information varies according to the chip carrier. Select the appropriate APN from the list below.

APN*allcom.br*allcom*allcom

APN*bws.br*bws*bws

APN*claro.com.br*claro*claro

APN*datelo.com.br*algar*algar

APN*federal.br*federal*federal

APN*g.claro.com.br*claro*claro

APN*hinova.br*hinova*hinova

APN*jbgprs.br*arqia*arqia

APN*linksolutions.br*link*link

APN*m2data.algar.br*algar*algar

APN*m2data.arqia.br*arqia*arqia

APN*m2data.claro.com.br*claro*claro

APN*m2m.arqia.br*arqia*arqia

APN*m2track.br*vivo*vivo

APN*meta.br*algar*algar

APN*meta.br*arqia*arqia

APN*meta.vivo.com.br*vivo*vivo

APN*powertech.algar*algar*1212

APN*smart.m2m.vivo.com.br*vivo*vivo

APN*transmeet.br*transmeet*transmeet

APN*virtueyes.com.br*virtu*virtu

APN*voxter.br*algar*algar

APN*voxter.br*nlt*nlt

APN*wl.vivo.com.br*vivo*vivo

APN*zap.vivo.com.br*vivo*vivo

Make sure to enter the correct data for your carrier.

5. DNS and Port Configuration

Configure the DNS servers as indicated, using the DNS command for each server.

DNS#central.trackar.com.br#6056#

DNS#central.trackar.com.br#6056#

DNS#central.trackar.com.br#6056#

6. Transmission Interval in Motion

Adjust the data transmission interval while the device is in motion. The default value is 60 seconds, using the command HB60.

HB60

7. Stopped Transmission Interval

Set the transmission interval when the vehicle is stopped, which can be adjusted to 3300 seconds with the command SHB3300.

SHB3300

Special commands

8. Special Commands

Use the commands below to manage specific functions of the tracker.

ENGOFF

ENGON

TURNDETON

TURNDETOFF

BJ0

JD0

check

status

CXIP

dns

google

loca

LBS

ICCID

ET

dk0

RESTART

RST