Installation Manual for Jimi NT202

Introduction to the Installation Manual for Jimi NT202

The Jimi NT202 is an advanced GPS tracking device designed to provide accuracy and reliability in locating vehicles and objects. This physical installation manual will provide essential guidance on how to properly position the GPS, ensure adequate power supply, install the SIM chip, and perform a functionality check of the device.

For effective installation, it is crucial to choose a location that minimizes interference and maximizes GPS signal reception. Additionally, the connection to the power supply must be made carefully, ensuring that the device is always active. The installation of the SIM chip also requires specific care, as it is crucial for data communication. Finally, verifying the operation of the Jimi NT202 is an essential step to ensure that all functionalities are operating correctly.

Following these instructions will help ensure that you make the most of your Jimi NT202's capabilities. To efficiently manage and monitor all tracking information, consider using the Trackar platform, which offers a one-time payment solution, facilitating your tracking experience.

SMS Commands

1. Time Zone Configuration

The first step is to correctly adjust the device's time zone. This is essential to ensure that location information is recorded accurately.

GMT,W,0#

2. Angle Position Configuration

Set the position by angle in degrees. You can adjust the detection range for curved points, where the value 0 disables this function. This is useful for optimizing tracking accuracy.

BEND,1,30#

3. Transmission Time in Motion

Adjust the transmission time interval while the device is in motion. The time can be set in seconds, with a default of 60 seconds.

TIMER,60#

4. Transmission Time Stationary

Configure the transmission time when the device is stationary. This time is adjustable in minutes, with the default set to 55 minutes.

STATIC,55#

5. Emergency Time

This command sets the emergency time, which allows location sending in case of a main power cut. The default value is 10 seconds.

EMERG,10#

6. Accelerometer Sensitivity

The accelerometer sensitivity can be adjusted in a range from 1 to 5, where 1 represents the most sensitive setting. This helps detect movements with greater accuracy.

VIBRATION,3#

7. Communication Protocol

Set the device's communication protocol to ensure an effective connection with the tracking platform.

SETLOCX12#

8. DNS and Port Configuration

It is necessary to configure the DNS server and port to ensure that the tracker connects correctly to the tracking platform. Three servers are provided as examples.

SERVER,8520,central.trackar.com.br,5013#

9. Carrier APN Configuration

The APN configuration is crucial and must be done based on the correct information provided by the chip carrier. Each carrier may have different settings that need to be adjusted.

APN,ALLCOM.ALGAR.BR,ALLCOM,ALLCOM#

APN,ALLCOM.BR,ALLCOM,ALLCOM#

APN,ALLCOM.VIVO.COM.BR,ALLCOM,ALLCOM#

APN,CLARO.COM.BR,CLARO,CLARO#

APN,ESEYE.COM#

APN,GPRS.OI.COM.BR,OI,OI#

APN,GPRS.TELEMIGCELULAR.COM.BR#

APN,IOT4U.BR,ARQIA,ARQIA#

APN,JBGPRS.BR,ARQIA,ARQIA#

APN,KORE.BR,KORE,KORE#

APN,LINKSOLUTIONS.BR#

APN,M2DATA.ALGAR.BR,ALGAR,ALGAR#

APN,M2DATA.ARQIA.BR#

APN,M2DATA.VIVO.COM.BR#

APN,M2M.VODAFONE.BR,VODAFONE,VODAFONE#

APN,OKTOR.BR,OKTOR,OKTOR#

APN,POWERTECH,ALGAR,1212#

APN,SMART.M2M.VIVO.COM.BR,VIVO,VIVO#

APN,SS.ALGAR.BR,ALGAR,ALGAR#

APN,TIM.BR,TIM,TIM#

APN,TRANSMEET.BR,TRANSMEET,TRANSMEET#

APN,VIRTUEYES.VIVO.COM.BR#

APN,VOXTER.ALGAR.BR#

APN,VOXTER.BR#

APN,ZAP.VIVO.COM.BR,VIVO,VIVO#

APN.BRT.BR#

APN.META.VIVO.COM.BR,META,META#

APN.NLT.COM.BR,NLT,NLT#

10. Force Position Communication

This command allows forcing a position communication via GPRS, useful to ensure that the location is updated in real time.

123

End of recommended settings.

Special commands

Special Commands

Below are the special commands that can be used to manage the tracker.

DYD,000000#

HFYD,000000#

RESET#

CLRG#

PARAM#

STATUS#

ACCVIRTON#

ACCVIRTOFF#

YSJ010#

GPS#

HBT,1#

URL#

WAKE,1#

SLEEP,5#

SLPON#

SLPOFF#

POWER1#

POWER0#

RELAY,1#

RELAY,0#

FACTORY#

Make sure the device is updated to use all commands.