Installation Manual for Concox Start S-2013

Introduction to the Installation Manual for the Concox Start S-2013

The Concox Start S-2013 is a GPS tracking device designed to provide effective and secure monitoring solutions. To ensure its full functionality, it is essential to follow the physical installation guidelines, which cover the GPS position, power connection, SIM card insertion, and system verification.

Choosing the location for installing the Concox Start S-2013 is crucial. The device should be positioned in a location that minimizes GPS signal obstruction, such as under the vehicle's dashboard or in less isolated areas. Additionally, the power connection must be made properly to ensure that the device operates continuously without interruptions.

Inserting the SIM card is another important step, as it is responsible for the device's communication with the network. After the physical installation, it is essential to perform a check to ensure that the Concox Start S-2013 is operating correctly, enabling real-time tracking.

To further facilitate the management of your device, consider using the Trackar platform, which offers a one-time payment service for complete and efficient control of your tracker. Proper installation of your Concox Start S-2013 is the first step to ensuring safety and effective monitoring.

SMS Commands

1. Time Zone Configuration

To ensure that the tracker works correctly, it is essential that the time zone is configured. The configuration must be done through the appropriate command.

GMT,W,0,0#

2. Update Interval Configuration

The update interval of the tracker can be adjusted in seconds. It is possible to set different intervals for when the vehicle is in motion and when it is stationary.

TIMER,20,20#

3. Angle-Based Update

The location update of the tracker can be configured based on a specific angle and an adjustable detection time. This allows for greater accuracy in location.

ANGLEREP,ON,30,2#

4. Heartbeat Configuration

The heartbeat is a signal of life that the tracker sends at regular intervals. It is possible to adjust these intervals based on the vehicle's ignition state.

HB,1,55#

5. Server Configuration

It is necessary to configure the server address and port for the tracker to send data correctly. Make sure the information is accurate.

SERVER,1,central.trackar.com.br,5019,0#

6. APN Configuration

APN, username, and password settings are fundamental and must be entered correctly according to the carrier of the used chip.

APN,AGILIS.ALGAR.BR#

APN,ALLCOM.ALGAR.BR#

APN,ALLCOM.BR#

APN,ALLCOM.VIVO.COM.BR#

APN,CLARO.COM.BR#

APN,DATATEM.ALGAR.BR#

APN,ESEYE.COM#

APN,GPRS.OI.COM.BR,OI,OI#

APN,GPRS.TELEMIGCELULAR.COM.BR#

APN,IOT4U.BR#

APN,JBGPRS.BR#

APN,LINKSOLUTIONS.BR#

APN,M2DATA.ALGAR.BR#

APN,M2DATA.ARQIA.BR#

APN,M2DATA.VIVO.COM.BR#

APN,M2M.VODAFONE.BR#

APN,M2TRACK.BR#

APN,OKTOR.BR#

APN,SMART.M2M.VIVO.COM.BR#

APN,SS.ALGAR.BR#

APN,TIM.BR,TIM,TIM#

APN,TRANSMEET.BR#

APN,VIRTUEYES.VIVO.COM.BR#

APN,VOXTER.ALGAR.BR#

APN,VOXTER.BR#

APN,ZAP.VIVO.COM.BR#

APN.BRT.BR#

APN.META.VIVO.COM.BR#

7. Forced Position Sending

To ensure that positions are sent, you can force the tracker to send data for a period of 5 minutes. This is useful for functionality testing.

LJDW#

Special commands

Special Commands

Here are some special commands that can be used for different functions of the tracker.

PARAM#

GPRSSET#

STATUS#

STA_SENDGPS,1#

STA_SENDGPS,0#

STA_SENDGPS#

SENDS,0#

SOS,A,XXXXXXXXXXX#

CENTER,A,XXXXXXXXXXX#

CENTER,D#

SOS,D,XXXXXXXXXXX#

RELAY,1#

RELAY,0#

ANGLEREP,ON,30,2#

ICCID#

HBT,1,55#

DW#

WHERE#

RESET#

FACTORY#

Note: the use of some commands may affect the vehicle's battery consumption.