Installation Manual for Concox Start S-2012

Introduction to the Installation Manual for Concox Start S-2012

The Concox Start S-2012 is an advanced GPS tracking device, ideal for accurately and efficiently monitoring vehicle locations. The physical installation of this equipment is a crucial step to ensure its proper functioning. It is essential to choose the correct position for the GPS, ensuring that it has a clear view of the sky to optimize signal reception. Additionally, the device's power supply must be handled carefully, connecting it to the appropriate power source.

Another important aspect is the installation of the SIM card, which must be inserted correctly for the Concox Start S-2012 to connect to the data network. After installation, it is advisable to conduct a thorough check to ensure that the device is functioning perfectly and transmitting location information reliably.

For an even more complete tracking experience, consider using the Trackar platform, which offers a one-time payment system and various features to optimize your fleet management. Install your Concox Start S-2012 and start monitoring efficiently!

SMS Commands

1. Time Zone Configuration

It is essential that the device's time zone is set correctly to ensure that location information is accurate. The command must be sent according to the GMT standard.

GMT,W,0,0#

2. Update Time Configuration

The update time can be adjusted according to need. The transmission interval while moving and stationary can be configured to optimize device usage.

TIMER,20,20#

X represents the interval while moving and Y while stationary.

3. Angle Update

Location updates can be made based on a specific angle and detection time. This is useful for tracking in specific situations.

ANGLEREP,ON,30,2#

The angle is defined in degrees and the time in seconds.

4. Heartbeat Configuration

The heartbeat interval can be adjusted in minutes, allowing the tracker to send signals under different ignition conditions.

HB,1,55#

X is the time with ignition on and Y with ignition off.

5. Server and Port Configuration

It is necessary to correctly configure the server and port to ensure that the tracker connects to the network. This command must be sent for each server.

SERVER,1,central.trackar.com.br,5019,0#

6. Carrier APN Configuration

Correct APN configuration is crucial for the tracker’s communication with the network. The information must be adjusted according to the carrier and the chip used.

APN,AGILIS.ALGAR.BR#

APN,ALLCOM.ALGAR.BR#

APN,ALLCOM.BR#

APN,ALLCOM.VIVO.COM.BR#

APN,CLARO.COM.BR#

APN,DATATEM.ALGAR.BR#

APN,ESEYE.COM#

APN,GPRS.OI.COM.BR,OI,OI#

APN,GPRS.TELEMIGCELULAR.COM.BR#

APN,IOT4U.BR#

APN,JBGPRS.BR#

APN,LINKSOLUTIONS.BR#

APN,M2DATA.ALGAR.BR#

APN,M2DATA.ARQIA.BR#

APN,M2DATA.VIVO.COM.BR#

APN,M2M.VODAFONE.BR#

APN,M2TRACK.BR#

APN,OKTOR.BR#

APN,SMART.M2M.VIVO.COM.BR#

APN,SS.ALGAR.BR#

APN,TIM.BR,TIM,TIM#

APN,TRANSMEET.BR#

APN,VIRTUEYES.VIVO.COM.BR#

APN,VOXTER.ALGAR.BR#

APN,VOXTER.BR#

APN,ZAP.VIVO.COM.BR#

APN.BRT.BR#

APN.META.VIVO.COM.BR#

7. Force Position Sending

To ensure that the tracker sends positions in real time, you can force sending during a specific period. This command should be used with caution.

LJDW#

The sending will be performed for 5 minutes.

Special commands

1. Check Settings

This command allows you to check the current settings of the tracker, including APN and server.

PARAM# ### 2. Check Status

Check the current status of the tracker to ensure everything is working correctly.

STATUS# ### 3. Activate Satellite Receiver

Activate the satellite receiver when the vehicle is stationary, knowing that this may consume more battery.

STA_SENDGPS,1#

Battery consumption will be higher. ### 4. Deactivate Satellite Receiver

Deactivate the satellite receiver when the ignition is off to save battery.

STA_SENDGPS,0# ### 5. Check Receiver Settings

Check the satellite receiver settings to ensure proper operation.

STA_SENDGPS# ### 6. Always On Satellite Receiver

Keep the satellite receiver always active, adjusting the time as needed. This mode may consume more battery.

SENDS,0#

0 means that the GPS will always be on. ### 7. Add SOS

Set up an emergency number for quick contact in case of need.

SOS,A,XXXXXXXXXXX# ### 8. Add Control Center

Add a control center number for monitoring the tracker.

CENTER,A,XXXXXXXXXXX# ### 9. Delete Control Center

Remove a previously configured number as a control center.

CENTER,D# ### 10. Delete SOS

Remove a previously configured emergency number.

SOS,D,XXXXXXXXXXX# ### 11. Lock Device

Activate the tracker lock to increase vehicle security.

RELAY,1# ### 12. Unlock Device

Deactivate the tracker lock when necessary.

RELAY,0# ### 13. Set Angle

Configure a specific angle for the tracker’s location update.

ANGLEREP,ON,30,2# ### 14. Check Chip ICCID

Check the identification number of the chip used in the device.

ICCID# ### 15. Generate Information Packets

Activate the generation of packets with complete information from the tracker.

HBT,1,55# ### 16. Check Location

Obtain the date, location, and a link to Google Maps with the tracker’s coordinates.

DW# ### 17. Check Movement Data

Check the latitude, longitude, course, speed, date, and time information of the tracker.

WHERE# ### 18. Restart Tracker

Restart the device to resolve issues or apply new settings.

RESET# ### 19. Restore Factory Settings

Restore the tracker to its original factory settings.

FACTORY#