Concox SL48 Installation Manual

Introduction to the Concox SL48 Installation Manual

The Concox SL48 is an advanced GPS tracking device designed to provide accuracy and reliability in its applications. To ensure optimal performance, the correct physical installation of the device is essential. In this section, we will address the main aspects of installation, including choosing the GPS position, connecting power, installing the SIM chip, and verifying the device's operation.

The GPS position should be chosen carefully, ensuring that the signal is not obstructed by metal or other interferences. The power supply should be connected according to the manufacturer's specifications, ensuring that the device has sufficient energy to operate continuously. Installing the SIM chip is another crucial step, as it ensures effective communication between the device and the network. Finally, a thorough check of the Concox SL48's operation is essential to confirm that all steps have been performed correctly and that the device is ready for use.

Make the most of your Concox SL48's functionalities by integrating it with the Trackar platform, which offers an efficient tracking system with a one-time payment. Ensure your security and monitoring today!

SMS Commands

1. Time Zone Configuration

It is essential to adjust the GPS tracker’s time zone to ensure that location information is accurate. Use the appropriate command to set the GMT and the hour difference.

GMT,W,0,0#

2. Update Interval Configuration

Transmission intervals can be adjusted according to need. You can set different times for when the vehicle is in motion and when it is stationary.

TIMER,20,20#

X represents the interval in motion, while Y is for the interval when stationary.

3. Angle-Based Update

Location updates can be configured to occur based on a specific angle. This allows the tracker to be more efficient in certain situations.

ANGLEREP,ON,30,2#

The angle is defined in degrees and the detection time in seconds.

4. Heartbeat Configuration

The heartbeat interval can be adjusted to optimize battery usage. This sets the frequency with which the tracker sends information when the ignition is on or off.

HB,1,55#

5. Server and Port Configuration

Configure the server and port to ensure that the tracker connects correctly to the network. It is important to verify that the information is correct.

SERVER,1,central.trackar.com.br,5023,0#

SERVER,1,central.trackar.com.br,5023,0#

SERVER,1,central.trackar.com.br,5023,0#

6. APN Configuration

APN configuration is crucial for the tracker’s operation. The information must be adapted according to the carrier used. Check each of the listed commands.

APN,AGILIS.ALGAR.BR#

APN,ALLCOM.ALGAR.BR#

APN,ALLCOM.BR#

APN,ALLCOM.VIVO.COM.BR#

APN,CLARO.COM.BR#

APN,DATATEM.ALGAR.BR#

APN,ESEYE.COM#

APN,GPRS.OI.COM.BR,OI,OI#

APN,GPRS.TELEMIGCELULAR.COM.BR#

APN,IOT4U.BR#

APN,JBGPRS.BR#

APN,LINKSOLUTIONS.BR#

APN,M2DATA.ALGAR.BR#

APN,M2DATA.ARQIA.BR#

APN,M2DATA.VIVO.COM.BR#

APN,M2M.VODAFONE.BR#

APN,M2TRACK.BR#

APN,OKTOR.BR#

APN,SMART.M2M.VIVO.COM.BR#

APN,SS.ALGAR.BR#

APN,TIM.BR,TIM,TIM#

APN,TRANSMEET.BR#

APN,VIRTUEYES.VIVO.COM.BR#

APN,VOXTER.ALGAR.BR#

APN,VOXTER.BR#

APN,ZAP.VIVO.COM.BR#

APN.BRT.BR#

APN.META.VIVO.COM.BR#

APN, username, and password information must be updated according to the carrier.

7. Force Position Sending

If necessary, you can force the tracker to send its position for a specific period. This can be useful in emergency situations or intensive monitoring.

LJDW#

The tracker will send positions for 5 minutes.

Special commands

Special Commands

PARAM#

GPRSSET#

STATUS#

STA_SENDGPS,1#

STA_SENDGPS,0#

STA_SENDGPS#

SENDS,0#

SOS,A,XXXXXXXXXXX#

CENTER,A,XXXXXXXXXXX#

CENTER,D#

SOS,D,XXXXXXXXXXX#

RELAY,1#

RELAY,0#

ANGLEREP,ON,30,2#

ICCID#

HBT,1,55#

DW#

WHERE#

RESET#

FACTORY#

These commands allow various additional functionalities and configurations of the tracker.