Coban TK106 Installation Manual

Introduction to the Coban TK106 Installation Manual

The Coban TK106 is a highly efficient GPS device designed to provide accurate and real-time tracking. In this manual, we will cover the essential steps for the physical installation of your GPS, ensuring that you make the most of its functionalities.

The correct installation of the Coban TK106 involves several fundamental steps, including choosing the ideal position for the device, connecting it to a power source, inserting the SIM card, and verifying its operation. The position of the GPS should be chosen to avoid obstructions and interference, allowing for optimized signal reception. Regarding power supply, it is crucial to ensure that the device is connected to an appropriate power source to guarantee its continuous operation. The insertion of the SIM card should be done carefully, ensuring it is correctly positioned to avoid communication failures. Finally, it is important to perform a verification of the device after installation, ensuring that all functions are operational and that tracking is being conducted accurately.

For complete and simplified monitoring, consider using the Trackar platform, which offers a one-time payment solution to manage your Coban TK106 efficiently.

SMS Commands

1. Equipment Setup Start

To start using the Coban TK106 tracker, you need to begin the device configuration. Use the command below to start the process.

begin123456

2. Time Zone Configuration

Adjust the time zone of the tracker to ensure that location information is accurate. Use the appropriate command with the administrator password.

time zone123456 0

3. Carrier APN Configuration

It is crucial to configure the APN correctly, as the information may vary depending on the chip carrier. Check the available APN commands and choose the one that applies to your carrier.

apn123456 algar.com.br

apn123456 allcom.br

apn123456 allcom.vivo.com.br

apn123456 brt.br

apn123456 claro.com.br

apn123456 conect.algar.br

apn123456 conexao.getrak.com.br

apn123456 core.br

apn123456 datatem.algar.br

apn123456 eseye.com

apn123456 federal.br

apn123456 gprs.amazoniacelular.com.br

apn123456 gprs.oi.com.br

apn123456 gprs.telemigcelular.com.br

apn123456 hinova.br

apn123456 jbgprs.br

apn123456 linksolutions.br

apn123456 m2data.algar.br

apn123456 m2data.arqia.br

apn123456 m2data.claro.com.br

apn123456 m2data.vivo.com.br

apn123456 m2m.vodafone.br

apn123456 m2track.br,vivo,vivo#

apn123456 meta.vivo.com.br

apn123456 mgdata.claro.com.br

apn123456 oktor.br

apn123456 sercomtel.com.br

apn123456 smart.m2m.vivo.com.br

apn123456 ss.algar.br

apn123456 ss.claro.com.br

apn123456 tim.br

apn123456 tmdata.tim.br

apn123456 transmeet.br

apn123456 upchip.br

apn123456 virtueyes.vivo.com.br

apn123456 voxter.algar.br

apn123456 voxter.br

apn123456 wap.ctbc.br

apn123456 wl.vivo.com.br

apn123456 y1.m2m.algar.com.br

apn123456 zap.vivo.com.br

Make sure that the APN, username, and password are correct.

4. DNS and Port Configuration

Set the DNS servers and the port for data transmission. It is important that these values are correct to ensure communication between the tracker and the server.

dns123456 central.trackar.com.br 6001

5. Tracking Mode

Activate the device's tracking mode so that it starts sending real-time location information.

tracker123456

6. Enable GPRS Transmission

Activate data transmission via GPRS so that the tracker can communicate with the server.

gprs123456

7. Force GPRS Transmission

If necessary, you can force GPRS transmission using the command below. This is useful in situations where the connection is not being established.

gprs123456 on

8. Smart Tracking Mode

Activate smart tracking mode, which saves chip data. The transmission time can be adjusted as needed.

fix060s055m***n123456

The smart mode sets the transmission to every 60 seconds with the ignition on and every 55 minutes with the ignition off.

9. Position Sending by Angle

Configure the tracker to send position by angle, adjusting as needed. Remember that some versions do not accept leading zeros.

angle123456 020

If your line has active SMS return and receives the warning: 'format error only support 3 digits', use the command without the leading zero, for example, 'angle123456 20'.

10. Activate Fuel Sensor Status

Enable the function that improves the transmission of digital sensor statuses, including the fuel sensor.

protocol123456 18

11. Turn on Data Saving

Activate data saving so that the tracker stops sending the position when the vehicle has been stationary for more than 10 minutes.

less gprs123456 on

12. GPS Shutdown

Configure the tracker so that GPS data stops being updated when the vehicle is not in motion. Updates will automatically resume when the vehicle starts moving again.

nosuppress123456

This setting is recommended to save battery.

Special commands

Special Commands

Below are some special commands that can be used to query information and manage the tracker.

check123456

reset123456

fix030s***n123456

nofix123456

stop123456

resume123456

quickstop123456

noquickstop123456

imei123456

localization123456

address123456

acc123456

noacc123456

gprs123456,0,0

gprs123456,1,1

less gprs123456 off

sleep123456 shock

nosleep123456

arm123456

lowbattery123456 on

lowbattery123456 off

extpower123456 on

extpower123456 off

clear123456

distance123456 0050

password + senha_antiga + espaço + senha_nova

password123456 999999

Remember that the GSM signal must be greater than 10 to connect to the server.