Coban LK610 Installation Manual

Introduction to the Coban LK610 Installation Manual

The Coban LK610 is a highly efficient GPS tracking device designed to provide security and monitoring of vehicles in a practical and accessible way. In this manual, we will cover the essential aspects of the physical installation of the device, including the correct GPS positioning, power supply, SIM chip installation, and verification of the equipment's functionality.

Choosing the ideal position for the Coban LK610 is crucial to ensure adequate GPS signal reception. It is recommended to install it in locations where there are no significant obstructions, such as inside metal compartments or under parts that may interfere with communication. Additionally, the device's power supply should be connected correctly to avoid operational failures.

Installing the SIM chip is also a crucial step, as it is through this that the device will connect to the mobile network to send location information. After installation, we will conduct a verification to ensure that the Coban LK610 is functioning correctly and sending data as expected.

To further optimize your tracking, consider using the Trackar platform, which offers a one-time payment service, allowing you to access advanced monitoring and security features for your vehicle.

SMS Commands

1. Start of Equipment Setup

To start using your tracker, you need to begin the device configuration. This ensures that all functions are operational and that the tracker is ready for use.

begin123456

2. Time Zone Configuration

Adjusting the time zone is essential to ensure that location data is accurate. Use the appropriate command to set the desired time zone.

time zone123456 0

3. Carrier APN Configuration

Configuring the APN is crucial, as the information may vary depending on the SIM card carrier used. Make sure to enter the correct data to ensure tracker connectivity.

apn,m2track.br,vivo,vivo#

apn123456 allcom.br

apn123456 allcom.vivo.com.br

apn123456 brt.br

apn123456 claro.com.br

apn123456 datatem.algar.br

apn123456 eseye.com

apn123456 gprs.amazoniacelular.com.br

apn123456 gprs.oi.com.br

apn123456 gprs.telemigcelular.com.br

apn123456 linksolutions.br

apn123456 m2data.algar.br

apn123456 m2data.arqia.br

apn123456 m2data.vivo.com.br

apn123456 m2m.vodafone.br

apn123456 m2mprepgago.br arqia arqia

apn123456 meta.vivo.com.br meta meta

apn123456 oktor.br

apn123456 sercomtel.com.br

apn123456 smart.m2m.vivo.com.br

apn123456 ss.algar.br

apn123456 tim.br

apn123456 tmdata.tim.br

apn123456 transmeet.br

apn123456 virtueyes.vivo.com.br

apn123456 voxter.algar.br

apn123456 voxter.br

apn123456 wap.ctbc.com.br

apn123456 wl.vivo.com.br

apn123456 y1.m2m.algar.com.br

apn123456 zap.vivo.com.br

4. DNS and Port Configuration

It is important to correctly configure the DNS server and port to ensure communication between the tracker and the central server. Use the following commands to perform this configuration.

SZCS,123456,DOMAIN=central.trackar.com.br:6013

5. Enable GPRS Transmission

Activate data transmission via GPRS so that the tracker can send location and status information. This is essential for the device's operation.

gprs123456

6. Tracking Mode

Activate tracking mode so that the device begins to monitor location in real-time. This mode is fundamental for the main functionality of the tracker.

tracker123456

7. Transmission Time Configuration

Set the interval at which the tracker will send location updates. A time of 60 seconds is recommended for effective tracking.

upload123456 60

8. Activate Vibration Alarm

Configure the vibration alarm so that the tracker can detect unexpected movements and alert you about possible interferences.

shock123456

9. Sleep Mode by Sensor

The tracker can enter hibernation mode after 5 minutes of inactivity. It will be activated again upon detecting any movement or vibration.

sleep123456 shock

Special commands

Special Commands

Use the special commands below to access additional functions and information from the tracker.

G123456

where

check123456

(s42,1234)

status

Param1

Param2

sos

sleep123456 10

sleep123456 shock

nosleep12345

shock123456

noshock123456

pwr1

pwr0

555

666

imei123456

rst

format