Coban Incutex TK105 Installation Manual

Introduction to the Coban Incutex TK105 Installation Manual

The Coban Incutex TK105 GPS is an advanced solution for vehicle monitoring and tracking, ideal for those seeking security and real-time control. In this manual, we will cover the essential steps for the physical installation of the device, ensuring that you make the most of its features.

First, it is crucial to find the ideal position for the GPS, which should be discreet and protected, yet still have good visibility for the signal. The device must be powered correctly by connecting it to the vehicle's power source, which will ensure its continuous operation. Additionally, do not forget to insert the SIM card, which will allow the device to communicate with the network.

After installation, verifying the operation is an important step. This ensures that the Coban Incutex TK105 is functioning correctly and sending accurate data to your monitoring platform. With these steps completed, you will be ready to explore all the features that your new GPS has to offer.

For an even more efficient tracking experience, consider the Trackar platform, which offers a one-time payment and advanced features to optimize the monitoring of your vehicle.

SMS Commands

1. Start Device Configuration

To start the configuration of the Coban TK105 tracker, it is necessary to send the initial command. This step is essential to proceed with the other device configurations.

begin123456

2. Set Time Zone

Adjust the time zone of the tracker to ensure that location information is accurate. Use the appropriate command to set the desired time zone.

time zone123456 0

3. Set Carrier APN

It is essential to correctly configure the APN data, username, and password. This information varies according to the carrier and the SIM card used. Check the list below for available APN commands.

apn123456 algar.com.br

apn123456 allcom.br

apn123456 allcom.vivo.com.br

apn123456 brt.br

apn123456 claro.com.br

apn123456 conect.algar.br

apn123456 conexao.getrak.com.br

apn123456 core.br

apn123456 datatem.algar.br

apn123456 eseye.com

apn123456 federal.br

apn123456 gprs.amazoniacelular.com.br

apn123456 gprs.oi.com.br

apn123456 gprs.telemigcelular.com.br

apn123456 hinova.br

apn123456 jbgprs.br

apn123456 linksolutions.br

apn123456 m2data.algar.br

apn123456 m2data.arqia.br

apn123456 m2data.claro.com.br

apn123456 m2data.vivo.com.br

apn123456 m2m.vodafone.br

apn123456 m2track.br,vivo,vivo#

apn123456 meta.vivo.com.br

apn123456 mgdata.claro.com.br

apn123456 oktor.br

apn123456 sercomtel.com.br

apn123456 smart.m2m.vivo.com.br

apn123456 ss.algar.br

apn123456 ss.claro.com.br

apn123456 tim.br

apn123456 tmdata.tim.br

apn123456 transmeet.br

apn123456 upchip.br

apn123456 virtueyes.vivo.com.br

apn123456 voxter.algar.br

apn123456 voxter.br

apn123456 wap.ctbc.br

apn123456 wl.vivo.com.br

apn123456 y1.m2m.algar.com.br

apn123456 zap.vivo.com.br

4. Set DNS and Port

Define the DNS servers and their respective ports to ensure communication between the tracker and the server. It is important that this information is correct for proper functioning.

dns123456 central.trackar.com.br,5013

5. Activate Tracking Mode

Activate the device's tracking mode so that it begins to send location information. This command is essential for the tracker to function.

tracker123456

6. Enable GPRS Transmission

Activate data transmission via GPRS so that the tracker can send information to the server. This step is crucial for the tracker to function.

gprs123456

7. Force GPRS Transmission

If GPRS transmission is not active, use this command to force the connection. This ensures that the tracker is always sending data.

gprs123456 on

8. Smart Tracking Mode

Activate the smart tracking mode that saves chip data. This mode adjusts the data transmission time according to the vehicle's state.

fix060s055m***n123456

Sets the transmission time to 60 seconds with the ignition on and 55 minutes with the ignition off.

9. Send Position by Angle

Adjust the angle for sending the vehicle's position. It is important that the value is correct to ensure the accuracy of the information.

angle123456 020

Some versions do not accept the zero at the beginning. If you receive an error message, use only the last two digits.

10. Activate Fuel Sensor

Activate the fuel sensor status to improve data transmission from the digital sensors of the tracker. This helps monitor fuel consumption.

protocol123456 18

11. Data Saving

Activate data saving so that the tracker stops sending information when the vehicle has been stationary for more than 10 minutes. As soon as movement is detected, it resumes sending.

less gprs123456 on

12. Turn Off GPS

Deactivate the GPS so that data stops being updated when the vehicle is stationary. Updates will resume as soon as the vehicle moves.

nosuppress123456

Special commands

1. Check Settings

Send this command to check the current status of the tracker, including information about the battery, GPRS connection, GPS signal, and other settings.

check123456

The response will include details such as: POWER, Battery, GPRS, GPS, ACC, Door, and GSM signal. ### 2. Restart Tracker

Use this command to restart the tracker by turning it off and on again. This can be useful for resolving connection issues.

reset123456 ### 3. Continuous Tracking Mode

Activate this mode for continuous tracking without data saving, adjusting the transmission time to 30 seconds.

fix030s***n123456 ### 4. Turn Off Tracking Mode

Deactivate the current tracking mode with this command, stopping data transmission.

nofix123456 ### 5. Lock Vehicle

Send this command to lock the vehicle remotely, preventing it from being started.

stop123456 ### 6. Unlock Vehicle

Use this command to unlock the vehicle that was previously locked, allowing it to be started again.

resume123456 ### 7. Activate Immediate Lock Function

Activate this function to immediately lock the vehicle in case of emergency.

quickstop123456 ### 8. Deactivate Immediate Unlock Function

Deactivate the immediate unlock function to ensure that the vehicle remains locked.

noquickstop123456 ### 9. Check IMEI

Send this command to obtain the IMEI of the tracker, which is a unique identifier for the device.

imei123456 ### 10. Location Link

This command generates a link that allows access to the current location of the tracker.

localization123456 ### 11. Request Address by Latitude and Longitude

Send this command to receive the address corresponding to the current latitude and longitude of the tracker.

address123456 ### 12. Activate Key Alarm

Activate the vehicle's key alarm with this command, increasing the security of the device.

acc123456 ### 13. Turn Off Key Alarm

Deactivate the vehicle's key alarm to allow normal operation without alarms.

noacc123456 ### 14. TCP Mode

Activate TCP mode for data transmission. This mode is a configuration option for the tracker’s communication.

gprs123456,0,0 ### 15. UDP Mode

Activate UDP mode for data transmission. This mode is an alternative to TCP mode.

gprs123456,1,1 ### 16. Turn Off Data Saving

Deactivate data saving so that the tracker continues sending information without restrictions.

less gprs123456 off ### 17. Enter Sleep Mode

Activate sleep mode to save battery when the vehicle is not in motion. The tracker will enter standby mode.

sleep123456 shock ### 18. Turn Off Sleep Mode

Deactivate sleep mode so that the tracker returns to normal operation.

nosleep123456 ### 19. Activate Door Sensor

Activate the door sensor to increase security and monitor whether the vehicle's door is open or closed.

arm123456 ### 20. Activate Low Battery Alarm

Activate the alarm that alerts when the tracker’s battery is low, ensuring that the device remains functional.

lowbattery123456 on ### 21. Turn Off Low Battery Alarm

Deactivate the low battery alarm to avoid constant notifications when the battery is at acceptable levels.

lowbattery123456 off ### 22. Activate Power Cut Alarm

Activate the alarm that notifies when the power to the tracker is cut, increasing the device's security.

extpower123456 on ### 23. Turn Off Power Cut Alarm

Deactivate the power cut alarm to avoid unnecessary notifications when the tracker is functioning normally.

extpower123456 off ### 24. Clear Tracker's Internal Memory

Send this command to clear the tracker’s internal memory, removing old data and ensuring that the device operates efficiently.

clear123456 ### 25. Send Position by Distance

Adjust the distance at which the tracker will send the position. This command overrides the smart tracking mode, allowing the tracker to send data based on the distance traveled.

distance123456 0050

The number must be a 4-digit value. ### 26. Change Tracker's Default Password

Send this command to change the tracker’s default password, ensuring greater security for the device.

password + senha_antiga + espaço + senha_nova

Example: password123456 999999 ### 27. Reset Password

Use this command to reset the tracker’s password if you have forgotten the current password.

reset123456

The GSM signal level must be greater than 10 to connect to the server.