Coban Coban GPS305 Installation Manual

Introduction to the Coban GPS305 Installation Manual

The Coban GPS305 is a high-precision vehicle tracking device designed to provide security and real-time control over vehicle location. In this manual, we will cover the physical installation of the GPS, which involves crucial aspects such as the device's position, connection to the power source, installation of the SIM card, and verification of the equipment's proper functioning.

Choosing the correct position to install the Coban GPS305 is essential to ensure effective tracking. It is recommended that the device be installed in a location that minimizes GPS signal obstruction, such as under the dashboard or in hidden but accessible areas for maintenance. The device's power supply should be connected carefully, using the vehicle's power source to ensure continuous operation.

Additionally, the insertion of the SIM card should be done with care, ensuring that the device is connected to a reliable data network. After installation, it is essential to conduct tests to verify that the Coban GPS305 is operating correctly, ensuring that all functionalities are available.

To optimize the use of your device, consider the Trackar platform, which offers a tracking service with a one-time payment, facilitating efficient fleet management.

SMS Commands

1. Start of Equipment Configuration

To start the configuration of the Coban GPS305 tracker, it is essential to send an initial command that activates the device. This step is crucial to ensure that all subsequent settings are applied correctly.

begin123456

2. Time Zone Configuration

Adjusting the time zone of the tracker is essential for accurate location data. The command must be sent with the correct value of the desired time zone, which can be adjusted according to the location.

time zone123456 0

3. Carrier APN Configuration

Configuring the APN is a critical step that allows the tracker to connect to the carrier's data network. It is important to remember that APN, username, and password information varies according to the chip supplier and the carrier used. Therefore, the correct data must be entered to ensure connectivity.

apn123456 allcom.br

apn123456 linksolutions.br

apn123456 m2data.arqia.br

apn123456 smart.m2m.vivo.com.br

apn123456 tim.br

apn123456 transmeet.br

apn123456 virtueyes.com.br

apn123456 zap.vivo.com.br

4. DNS and Port Configuration

Configuring the DNS servers is an important step to ensure that the tracker functions correctly. Although the specific commands for the servers are not listed, it is necessary to enter the correct addresses for the proper functioning of the device.

Server 01, Server 02, Server 03 must be defined.

5. Vibration Alarm Activation

The vibration alarm is a feature that allows the tracker to notify the user in case of unexpected movements. This command must be activated to ensure that the device is always monitoring any suspicious activity.

shock123456

6. Tracking Activation

For the tracker to start sending location data, it is necessary to activate the tracking function. This command ensures that the device is always sending information about its position.

tracker123456

7. GPRS Transmission Activation

GPRS transmission must be activated for the tracker to send location data to the server. This is an essential step to ensure that all information is transmitted correctly.

gprs123456

8. Transmission Time Setting

The transmission time can be adjusted to optimize data usage and the efficiency of the tracker. The default value is 60 seconds, but it can be adjusted according to the user's needs.

upload123456 060

Transmission time set to 60 seconds with the device in motion.

9. Sleep Mode by Sensor

This mode allows the tracker to enter a low power consumption state after 5 minutes of inactivity. The device will be activated again upon detecting movements, vibrations, or receiving an SMS or call.

sleep123456 shock

The tracker wakes up with movement, SMS, or call.

Special commands

Special Commands

In addition to the basic commands, there are special commands that allow additional functionalities for the tracker. These commands can be used to obtain specific information or change settings more directly.

G123456#

gprs123456 0

sensitivity123456 + selecionar número 1, 2 ou 3!

check123456

speed123456 080

nospeed123456

shock123456

noshock123456

lowbatsms123456 on

sleep123456 time

sleep123456 shock

sleep123456 off

imei123456

reset123456