How to configure the Concox Start S-2010 tracker

The Concox Start S-2010 tracker is a robust and efficient solution for those looking to monitor the location of vehicles or other assets accurately and in real-time. To ensure the proper functioning of the device, it is essential to correctly configure the APN settings, DNS server, and IMEI, as well as perform connectivity tests.

In this section, we will guide you through the process of configuring your Concox Start S-2010, addressing each of the fundamental steps so that you can make the most of the features this equipment offers. Effective management of network parameters is crucial for the performance of the tracker, as inadequate configuration can result in communication failures or inaccurate data.

Make sure to carefully follow the instructions and verify each configuration so that the device connects correctly to the desired platform. After configuration, it is recommended to perform tests to confirm that everything is working as expected.

If you are not yet familiar with the Trackar platform, consider that it offers a one-time payment service, allowing access to advanced features for monitoring and managing your assets. Don’t miss the opportunity to optimize your experience with the Concox Start S-2010!

SMS Commands

1. Time Zone Configuration

It is essential to start configuring your tracker by adjusting the time zone. This ensures that all location and time information is correct and synchronized with your region.

GMT,W,0,0#

2. Update Interval Adjustment

Set the time interval at which the tracker will send updates of its location. You can adjust the time for different conditions: moving and stationary. This helps optimize battery usage and the accuracy of information.

TIMER,20,20#

3. Angle Update

Configure the tracker to update its location based on a specific angle. This allows the device to respond to changes in direction more efficiently, increasing the accuracy of updates.

ANGLEREP,ON,30,2#

4. Heartbeat

Adjust the interval for sending information from the tracker based on the vehicle's ignition status. This helps save battery when the vehicle is off but ensures you receive updates when necessary.

HB,1,55#

5. Server Configuration

It is important to configure the server correctly to ensure that the tracker data is sent to the correct platform. You can set the primary server and backups.

SERVER,1,central.trackar.com.br,5019,0#

6. APN Configuration

The APN configuration is crucial for the tracker to connect to the carrier's network. The APN, username, and password information must be entered correctly, as they vary according to the carrier providing the chip.

APN,AGILIS.ALGAR.BR#

APN,ALLCOM.ALGAR.BR#

APN,ALLCOM.BR#

APN,ALLCOM.VIVO.COM.BR#

APN,CLARO.COM.BR#

APN,DATATEM.ALGAR.BR#

APN,ESEYE.COM#

APN,GPRS.OI.COM.BR,OI,OI#

APN,GPRS.TELEMIGCELULAR.COM.BR#

APN,IOT4U.BR#

APN,JBGPRS.BR#

APN,LINKSOLUTIONS.BR#

APN,M2DATA.ALGAR.BR#

APN,M2DATA.ARQIA.BR#

APN,M2DATA.VIVO.COM.BR#

APN,M2M.VODAFONE.BR#

APN,M2TRACK.BR#

APN,OKTOR.BR#

APN,SMART.M2M.VIVO.COM.BR#

APN,SS.ALGAR.BR#

APN,TIM.BR,TIM,TIM#

APN,TRANSMEET.BR#

APN,VIRTUEYES.VIVO.COM.BR#

APN,VOXTER.ALGAR.BR#

APN,VOXTER.BR#

APN,ZAP.VIVO.COM.BR#

APN.BRT.BR#

APN.META.VIVO.COM.BR#

7. Force Position Sending

Use this command to force the tracker to send its location every 5 minutes. This can be useful in situations where it is necessary to monitor the vehicle's position in real-time.

LJDW#

Special commands

Special Commands

Below are some special commands that can be used to query and modify the tracker settings.

PARAM#

GPRSSET#

STATUS#

STA_SENDGPS,1#

STA_SENDGPS,0#

STA_SENDGPS#

SENDS,0#

SOS,A,XXXXXXXXXXX#

CENTER,A,XXXXXXXXXXX#

CENTER,D#

SOS,D,XXXXXXXXXXX#

RELAY,1#

RELAY,0#

ANGLEREP,ON,30,2#

ICCID#

HBT,1,55#

DW#

WHERE#

RESET#

FACTORY#

Attention: some commands may consume more battery from the vehicle.