How to configure the Coban TK102 tracker

The Coban TK102 tracker is a powerful tool for monitoring vehicles and objects, offering a range of features that ensure safety and efficiency. To make the most of this device, it is essential to correctly configure the APN, DNS server, and IMEI. In this introduction, you will learn how to make these fundamental adjustments so that your tracker operates optimally.

Configuring the APN is a critical step, as it ensures that the TK102 connects to the mobile data network, allowing for real-time location information to be sent. Additionally, setting the DNS server is important for the device to resolve addresses effectively. The IMEI, in turn, is the unique identifier of your tracker and must be correctly configured to avoid connectivity issues.

After following these steps, it is advisable to conduct tests to ensure that all configurations are functioning as expected. This will ensure that you have a fully operational tracker, ready to provide accurate and reliable location data.

For an even more complete experience, consider using the Trackar platform, which offers a one-time payment solution for monitoring and managing trackers. Don't miss the opportunity to optimize your use of the Coban TK102!

SMS Commands

1. Equipment Setup Start

To start the configuration of the Coban TK102 tracker, send the initialization command. This step is essential for the device to operate correctly.

begin123456

2. Time Zone Configuration

It is important to adjust the time zone of the tracker to ensure that location information is accurate. The command should be sent with the desired time zone value.

time zone123456 0

3. Carrier APN Configuration

The APN configuration is crucial, as each carrier has specific information. Make sure to enter the correct data from your provider so that the tracker works properly.

apn123456 algar.com.br

apn123456 allcom.br

apn123456 allcom.vivo.com.br

apn123456 brt.br

apn123456 claro.com.br

apn123456 conect.algar.br

apn123456 conexao.getrak.com.br

apn123456 core.br

apn123456 datatem.algar.br

apn123456 eseye.com

apn123456 federal.br

apn123456 gprs.amazoniacelular.com.br

apn123456 gprs.oi.com.br

apn123456 gprs.telemigcelular.com.br

apn123456 hinova.br

apn123456 jbgprs.br

apn123456 linksolutions.br

apn123456 m2data.algar.br

apn123456 m2data.arqia.br

apn123456 m2data.claro.com.br

apn123456 m2data.vivo.com.br

apn123456 m2m.vodafone.br

apn123456 m2track.br,vivo,vivo#

apn123456 meta.vivo.com.br

apn123456 mgdata.claro.com.br

apn123456 oktor.br

apn123456 sercomtel.com.br

apn123456 smart.m2m.vivo.com.br

apn123456 ss.algar.br

apn123456 ss.claro.com.br

apn123456 tim.br

apn123456 tmdata.tim.br

apn123456 transmeet.br

apn123456 upchip.br

apn123456 virtueyes.vivo.com.br

apn123456 voxter.algar.br

apn123456 voxter.br

apn123456 wap.ctbc.br

apn123456 wl.vivo.com.br

apn123456 y1.m2m.algar.com.br

apn123456 zap.vivo.com.br

4. DNS and Port Configuration

To ensure communication between the tracker and the servers, it is necessary to correctly configure the DNS servers and ports. Use the commands below to perform these configurations.

dns123456 central.trackar.com.br 6001

5. Tracking Mode Activation

Activate tracking mode so that the device starts sending its location. This command is fundamental for the tracker's operation.

tracker123456

6. Enable GPRS Transmission

It is necessary to enable GPRS transmission for the tracker to send data to the server. Use the command below to activate this function.

gprs123456

7. Force GPRS Transmission

If it is necessary to force data transmission via GPRS, use the command below. This can be useful in situations where the connection needs to be reestablished.

gprs123456 on

8. Smart Tracking Mode Configuration

The smart tracking mode allows saving data from the tracker's chip by adjusting the transmission time according to the vehicle's state. This command adjusts the transmission time to 60 seconds when the vehicle is on and 55 minutes when it is off.

fix060s055m***n123456

9. Position Sending by Angle

To adjust the position sending by angle, send the command with the desired value. Remember that some versions may not accept leading zeros.

angle123456 020

If you receive a format error, try sending the command without the leading zero, for example: angle123456 20.

10. Fuel Sensor Activation

Activate the fuel sensor status to improve data transmission from digital sensors. This will help better monitor the vehicle's condition.

protocol123456 18

11. Activate Data Saving

With data saving activated, the tracker will stop sending the position when the vehicle is stationary for more than 10 minutes. It will reactivate transmission as soon as the vehicle moves or an alarm is triggered.

less gprs123456 on

12. GPS Shutdown

When the vehicle is not moving, GPS updates will be stopped. As soon as the vehicle moves, updates will automatically resume.

nosuppress123456

Special commands

1. Check Settings

Use this command to check the current status of the tracker, including information about the battery, GPRS connection, GPS signal, and engine status.

check123456

The response will include details such as: POWER, Battery, GPRS, GPS, ACC, Door, and GSM signal. ### 2. Restart the Tracker

If there is a need to restart the tracker, use the command below to turn it off and back on.

reset123456 ### 3. Continuous Tracking Mode

Activate continuous tracking mode so that the tracker sends data without saving chip data. The transmission time will be adjusted to 30 seconds.

fix030s***n123456 ### 4. Turn Off Tracking Mode

To deactivate the tracking mode, use the corresponding command. This will stop sending location data.

nofix123456 ### 5. Lock the Vehicle

Send this command to remotely lock the vehicle. This function is useful for security.

stop123456 ### 6. Unlock the Vehicle

If the vehicle is locked, use this command to unlock it.

resume123456 ### 7. Activate Immediate Vehicle Lock

This command activates the immediate lock of the vehicle, ensuring security in emergency situations.

quickstop123456 ### 8. Deactivate Immediate Vehicle Lock

Use this command to deactivate the immediate lock of the vehicle.

noquickstop123456 ### 9. Check IMEI

Send this command to obtain the IMEI number of the tracker, which is essential for device identification.

imei123456 ### 10. Location Link

This command generates a link that can be used to view the location of the tracker in real-time.

localization123456 ### 11. Request Address by Latitude and Longitude

With this command, you can request the address corresponding to a specific latitude and longitude.

address123456 ### 12. Activate Key Alarm

Activate the vehicle's key alarm using this command. It is an additional security measure.

acc123456 ### 13. Deactivate Key Alarm

If the key alarm is activated, use this command to deactivate it.

noacc123456 ### 14. TCP Mode

Activate TCP mode for the communication of the tracker with the server, using the appropriate command.

gprs123456,0,0 ### 15. UDP Mode

Activate UDP mode for the communication of the tracker with the server, using the corresponding command.

gprs123456,1,1 ### 16. Turn Off Data Saving

To deactivate data saving, use this command. This will cause the tracker to send data continuously.

less gprs123456 off ### 17. Enter Sleep Mode

Activate sleep mode, which puts the tracker in standby mode when there is no movement.

sleep123456 shock ### 18. Turn Off Sleep Mode

If the tracker is in sleep mode, use this command to deactivate it.

nosleep123456 ### 19. Activate Door Sensor

Activate the vehicle's door sensor using this command. This will help monitor the vehicle's security.

arm123456 ### 20. Activate Low Battery Alarm

Activate the low battery alarm to receive notifications when the tracker’s battery is low.

lowbattery123456 on ### 21. Deactivate Low Battery Alarm

Deactivate the low battery alarm using this command.

lowbattery123456 off ### 22. Activate Power Cut Alarm

Activate the power cut alarm to be notified when the power source of the tracker is disconnected.

extpower123456 on ### 23. Deactivate Power Cut Alarm

Deactivate the power cut alarm using this command.

extpower123456 off ### 24. Clear Tracker Internal Memory

Use this command to clear the internal memory of the tracker, ensuring that old data is removed.

clear123456 ### 25. Send Position by Distance

Configure the tracker to send location data based on the distance traveled. The value should be sent in meters.

distance123456 0050

This command overrides the smart tracking mode. ### 26. Change Tracker Default Password

To change the default password of the tracker, send the command with the old password and the desired new password.

password + senha_antiga + espaço + senha_nova (ex: password123456 999999)

Remember that the default password is 123456. ### 27. Reset Password

If you need to reset the password of the tracker, use the appropriate command.

password123456 999999

The GSM signal level must be greater than 10 to connect to the server.