How to Configure the Coban 306A Device via SMS

This guide shows how to connect the Coban 306A tracker to the platform using SMS commands. Send each command from the SIM card installed in the device, in the order indicated below.

SMS Commands

1. Start of Configuration

To begin the configuration of your Coban 306A tracker, you must send the initial command that activates the device. This is the first essential step to ensure that the tracker operates correctly.

begin123456

2. Time Zone Configuration

Adjust the time zone of the tracker to ensure that location information is accurate. This command allows you to set the time zone according to your region.

time zone123456 0

3. Carrier APN Configuration

It is crucial to configure the APN correctly, as the information may vary depending on the carrier of the SIM card used. Make sure to enter the correct data to ensure the tracker communicates with the network.

apn123456 algar.com.br

apn123456 allcom.br

apn123456 allcom.vivo.com.br

apn123456 brt.br

apn123456 claro.com.br

apn123456 conect.algar.br

apn123456 conexao.getrak.com.br

apn123456 core.br

apn123456 datatem.algar.br

apn123456 eseye.com

apn123456 federal.br

apn123456 gprs.amazoniacelular.com.br

apn123456 gprs.oi.com.br

apn123456 gprs.telemigcelular.com.br

apn123456 hinova.br

apn123456 jbgprs.br

apn123456 linksolutions.br

apn123456 m2data.algar.br

apn123456 m2data.arqia.br

apn123456 m2data.claro.com.br

apn123456 m2data.vivo.com.br

apn123456 m2m.vodafone.br

apn123456 m2track.br,vivo,vivo#

apn123456 meta.vivo.com.br

apn123456 mgdata.claro.com.br

apn123456 oktor.br

apn123456 sercomtel.com.br

apn123456 smart.m2m.vivo.com.br

apn123456 ss.algar.br

apn123456 ss.claro.com.br

apn123456 tim.br

apn123456 tmdata.tim.br

apn123456 transmeet.br

apn123456 upchip.br

apn123456 virtueyes.vivo.com.br

apn123456 voxter.algar.br

apn123456 voxter.br

apn123456 wap.ctbc.br

apn123456 wl.vivo.com.br

apn123456 y1.m2m.algar.com.br

apn123456 zap.vivo.com.br

APN information must be updated according to the carrier used.

4. DNS and Port Configuration

Configuring the DNS and port is crucial for the correct functioning of the tracker. You must enter the appropriate servers to ensure stable communication.

dns123456 central.trackar.com.br,5001

5. Tracking Mode

Activate the tracking mode of the device so that it starts sending location information. This step is essential for you to monitor the vehicle.

tracker123456

6. Enable GPRS Transmission

This command activates data transmission via GPRS, allowing the tracker to send location and status information to the server.

gprs123456

7. Force GPRS Transmission

Use this command to force data transmission via GPRS, ensuring that information is sent immediately.

gprs123456 on

8. Smart Tracking Mode

Activate smart tracking mode to optimize the use of chip data. This mode adjusts the transmission time according to the vehicle's state, saving resources.

fix060s055m***n123456

9. Position Sending by Angle

Set the angle for position sending. This adjustment allows the tracker to send location data based on a specific angle.

angle123456 020

Some versions may not accept the leading zero. If there is an error, remove the zero.

10. Activate Fuel Sensor Status

Activate the fuel sensor status to improve the data transmission of digital sensors. This command helps monitor the vehicle's fuel level.

protocol123456 18

11. Turn on Data Saving

Activate this function so that the tracker stops sending data when the vehicle is stationary for more than 10 minutes. As soon as the vehicle moves, transmission will resume.

less gprs123456 on

12. GPS Shutdown

This command disables GPS updates when the vehicle is not moving, saving battery. Updates will resume as soon as the vehicle moves.

nosuppress123456

Special commands

1. Check Settings

Use this command to check the current state of the tracker, including information about the battery, GPRS signal, GPS signal, and engine status.

check123456

The response will include detailed information about the state of the tracker. ### 2. Restart the Tracker

If the tracker presents problems, this command restarts the device, turning it off and on again.

reset123456 ### 3. Continuous Tracking Mode

Activate this mode for continuous tracking, without data saving, setting a transmission time of 30 seconds.

fix030s***n123456 ### 4. Turn Off Tracking Mode

Use this command to deactivate the current tracking mode if you need to stop data transmission.

nofix123456 ### 5. Lock and Unlock Vehicle

These commands allow you to lock or unlock the vehicle remotely, increasing security.

stop123456

resume123456 ### 6. Activate Immediate Lock Function

This command activates the immediate lock function of the vehicle, providing greater security in emergency situations.

quickstop123456 ### 7. Deactivate Immediate Unlock Function

Deactivate the immediate unlock function of the vehicle with this command, ensuring that the lock remains active.

noquickstop123456 ### 8. Check IMEI

Use this command to check the IMEI of the tracker, an important piece of information for device identification.

imei123456 ### 9. Location Link

This command generates a location link for the vehicle, facilitating real-time tracking.

localization123456 ### 10. Request Address by Latitude and Longitude

With this command, you can request the address corresponding to a certain latitude and longitude, facilitating location.

address123456 ### 11. Turn On and Off Key Alarm

Activate or deactivate the vehicle's key alarm with these commands, increasing the security of your vehicle.

acc123456

noacc123456 ### 12. TCP and UDP Mode

Configure the tracker to operate in TCP or UDP mode, depending on your data transmission needs.

gprs123456,0,0

gprs123456,1,1 ### 13. Turn Off Data Saving

Deactivate data saving so that the tracker sends information continuously, without interruptions.

less gprs123456 off ### 14. Enter Sleep Mode

This command puts the tracker in sleep mode when there is no movement, saving battery.

sleep123456 shock ### 15. Turn Off Sleep Mode

Deactivate the sleep mode of the tracker, allowing it to function normally.

nosleep123456 ### 16. Turn On Door Sensor

Activate the vehicle's door sensor to monitor whether the doors are open or closed.

arm123456 ### 17. Low Battery Alarm

Activate the low battery alarm to be notified when the tracker battery is low.

lowbattery123456 on ### 18. Turn Off Low Battery Alarm

Deactivate the low battery alarm with this command if you do not wish to receive notifications.

lowbattery123456 off ### 19. Power Cut Alarm

Activate the power cut alarm to be notified when the power to the tracker is interrupted.

extpower123456 on ### 20. Turn Off Power Cut Alarm

Deactivate the power cut alarm with this command if you do not wish to receive notifications.

extpower123456 off ### 21. Clear Internal Memory of Tracker

Use this command to clear the internal memory of the tracker, ensuring it operates efficiently.

clear123456 ### 22. Send Position by Distance

This command allows you to configure the tracker to send the position based on the distance traveled, in meters.

distance123456 0050

The number must be 4 digits. ### 23. Change Default Password of Tracker

To ensure the security of your device, you can change the default password. Use this command to make the change.

password + senha_antiga + espaço + senha_nova (ex: password123456 999999)

Make sure the new password is easy to remember but hard to guess. ### 24. Reset Password

If you have forgotten the password, use this command to reset the tracker password.

password123456 999999

Remember that the default password is 123456.